banner



Can I Connect Usb Cable To Service Port On Dynex Tv

Status
Not open up for further replies.
  • #i
I am trying to connect my computer to the Telly, but I'm receving no signal. I've followed the very minimal instructions in the transmission, simply still no point... I simply plugged the VGA cablevision from the reckoner to the Goggle box and the audio cable as instructed - no indicate. I changed the source on my TV to "VGA" as instructed - NO SIGNAL. There are no troubleshooting guidelines available, and then I tried to practise everything I know to troubleshoot myself. Any suggestions?
  • #two
it should take more i external input, try them all. (VGA-1, VGA-2, Digital, Digital-ane, etc)

Give me the best reply if this gets it going.

<edited past moderator>

Wolfshadw
Aug three, 2006
two,835
lx
26,290
708
  • #3
1) Bank check to make sure the Idiot box is enabled as a secondary monitor on your computer.
ii) You may need to change the resolution for the secondary monitor to something it will recognize.

-Wolf sends

November 24, 2011
ane
0
18,510
0
  • #4
Correct click on your desktop and select "screen resolution" --then play around with the setting to get your PC to detect the TV and display images on it instead of on the monitor your computer normally displays. This takes some lilliputian and I'grand not sure how I finally did it but eventually it worked.
popatim
Dec 2, 2009
2,358
4
24,965
754
  • #5
try setting your pc for 1280x720 @ 60hz display output.

Your user manual should show a listing of supported resolutions merely this should be one of them.

  • #half dozen
I am trying to connect my reckoner to the Telly, but I'chiliad receving no signal. I've followed the very minimal instructions in the transmission, but still no signal... I merely plugged the VGA cable from the estimator to the Telly and the audio cable as instructed - no signal. I changed the source on my TV to "VGA" equally instructed - NO Signal. There are no troubleshooting guidelines bachelor, and so I tried to do everything I know to troubleshoot myself. Any suggestions?

y found a solutyion gear up your video to

VGA input D-Sub fifteen-pin terminalE-EDID
compliantSuggested scan rates
:640×480 /threescore Hz,800×600 /60 Hz, 1024×768 /60 Hz,1360×768 /60 Hz,

Audio input: Headphone mini-jack for

  • #7
VGA input D-Sub 15-pin terminalE-EDID compliantSuggested browse rates:640×480 /lx Hz,800×600 /60 Hz, 1024×768 /60 Hz,1360×768 /60 Hz,Audio input: Headphone mini-jack for
Status
Not open up for further replies.
Thread starter Similar threads Forum Replies Date
J Streaming Video & TVs 6
9 Streaming Video & TVs 11
I Streaming Video & TVs two
B Streaming Video & TVs ane
D Streaming Video & TVs one
R Streaming Video & TVs 1
D Streaming Video & TVs 1
R Streaming Video & TVs 2
B Streaming Video & TVs 1
K Streaming Video & TVs 1
Q Streaming Video & TVs three
A Streaming Video & TVs 2
C Streaming Video & TVs 1
T Streaming Video & TVs one
M Streaming Video & TVs ane
K Streaming Video & TVs ane
T Streaming Video & TVs i
T Streaming Video & TVs 2
A Streaming Video & TVs 1
A Streaming Video & TVs 1
  • Advertising
  • Cookies Policies
  • Privacy
  • Term & Conditions
  • Topics

Can I Connect Usb Cable To Service Port On Dynex Tv,

Source: https://forums.tomsguide.com/threads/dynex-lcd-32-inch-tv-no-signal-from-computer-to-tv.214557/

Posted by: dickwaye1987.blogspot.com

0 Response to "Can I Connect Usb Cable To Service Port On Dynex Tv"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel